Skip to Content
ELECTROLESS NICKEL · SPECIFICATION GUIDE

MIL-C-26074 & AMS-C-26074: A Buyer's Guide

Learn how classes, grades and legacy drawing references affect an electroless nickel enquiry. Keep the exact specification and revision with your RFQ.

What is MIL-C-26074?

MIL-C-26074 is a legacy military specification for electroless nickel-phosphorus coatings on metal and composite surfaces. Older drawings may still cite it. The E revision, dated October 30, 1990, is the basis of the class and grade explanations below.

A legacy reference should travel with the drawing into the quoting process. Send the full designation, revision and any customer notes. A change to a different specification needs the authorization required by your contract and engineering documents.

This guide describes the historical requirement; it does not claim that every material, class or approval is available from ENTECH. Our team reviews the requested scope before accepting the work.

MIL-C-26074E classes: what happens after plating?

The class identifies the thermal-treatment category. It does not identify the coating thickness.

ClassPurpose in revision EBuyer consideration
1As-plated condition without a subsequent hardening or adhesion heat treatment.The E revision treats hydrogen embrittlement relief separately; Class 1 does not automatically mean no baking.
2Heat treatment to achieve the required coating hardness.Provide the alloy and condition so compatibility with the required treatment can be reviewed.
3Adhesion-focused processing for non-heat-treatable aluminum and beryllium alloys.Identify the exact material rather than describing all aluminum parts alike.
4Adhesion-focused processing for heat-treatable aluminum alloys.Include the alloy, temper and drawing instructions.

The controlled revision supplies the required cycles, tests and exceptions. These categories explain the callout; they are not oven operating instructions.

MIL-C-26074E grades: how much coating?

Grades A, B and C identify different minimum thicknesses. They are not rankings of overall quality.

GradeMinimum in revision EMetric conversion
A0.0010 inch25.4 µm
B0.0005 inch12.7 µm
C0.0015 inch38.1 µm

The metric figures above are direct conversions of the inch values for reader convenience. Revision E is an inch-pound document. Its substrate-specific default provisions and any drawing overrides must also be reviewed.

Example: “MIL-C-26074E, Class 1, Grade C”

E identifies the revision. Class 1 identifies the as-plated category, with hydrogen relief considered separately where required. Grade C identifies a 0.0015-inch minimum coating.

The callout still needs the rest of the drawing package: alloy and condition, coated surfaces, masking, final tolerances, inspection and customer requirements. This is an educational example, not a recommendation for a particular part.

How should I handle an AMS-C-26074 reference?

AMS-C-26074 is an SAE electroless nickel coating specification. SAE currently lists AMS-C-26074D as Stabilized. Review the edition required by the job rather than assuming that a historical cancellation notice applies to every revision.

MIL-C-26074, MIL-DTL-26074, AMS-C-26074 and AMS 2404 have distinct designations and document histories. Do not replace one with another on a purchase order without the necessary authorization.

SAE's AMS-C-26074D record · DLA's MIL-DTL-26074 document record

Send the document designation exactly as shown on your drawing. If it is incomplete or conflicts with the purchase order, identify the issue during the RFQ review.

MIL/AMS and ASTM terminology: avoid a common mix-up.

The historical MIL-C-26074E grade describes minimum thickness, while its class describes thermal treatment. ASTM B733 uses its own type, service-condition and class system. A matching number or letter is not evidence that two requirements are interchangeable.

Learn how to read ASTM B733 terminology →

What to send for a quote.

  • Drawing, part number and drawing revision.
  • Exact MIL or AMS designation and revision.
  • Specified class, grade, thickness, units and additional finish notes.
  • Base material, temper or hardness condition, critical dimensions and masking.
  • Quantity, required date, inspection and documentation requirements.
  • Any customer or program approval requirements.

ENTECH also offers oven baking and ASTM B117 salt spray testing and XRF analysis. Include the requirements applicable to your job so we can review the complete scope.

Questions buyers ask.

Does Class 1 mean hydrogen relief baking is unnecessary?

No. MIL-C-26074E distinguishes hydrogen embrittlement relief from the class-defining heat treatment. The material and applicable requirements determine whether relief is required.

Can I ask for a different grade to improve the part?

A different thickness can change fit and the drawing's requirements. Have the change reviewed and authorized before processing.

Can ENTECH review a legacy drawing?

Send the drawing, complete callout and purchase-order requirements. ENTECH will review the requested work and documentation before confirming suitability.

Where do the class and grade examples come from?

They summarize sections 1.2.1 and 1.2.2 of the historical U.S. military specification MIL-C-26074E, October 30, 1990. Use your organization's controlled copy for the complete requirements.

Educational reference: MIL-C-26074E (1990), sections 1.2 and 3. The publicly available historical government document was checked for the class and grade explanations. This page does not replace the controlled specification or establish customer approval.

Send the callout. We'll review the requirement.

Select the designation on your drawing to start your enquiry.